Download Ultimaker Cura 5.14.0

Pin this version: winget install --id Ultimaker.Cura --version 5.14.0 --exact

Release notes

New features and improvements: Paint-on-Support You can now define custom support areas by manually by painting regions to enforce, avoid, or auto-generate supports using an interactive overhang angle slider. You can also Paint Surface a surface by selecting an entire contiguous faces or curved features in a single click to apply paint on support or draw straight lines for paint on support using Shift and Shift + Ctrl shortcuts. You can now navigate the settings panel more easily with a tabbed organization layout by default, based on the Tabbed Settings plugin by @fieldofview and contributed by @HellAholic This version of Cura comes with a build for Windows on ARM, to help users with laptops who have a processor based on ARM architecture. If you have a Mac with ARM, those builds have been available for a while now. - Easily spot unsupported areas with distinct line-type colors for overhangs and bridges in the layer preview window. - Updated the skin strategy so that small roof and floor areas are printed in a unified way, reducing surface fragmentation and unnecessary travel moves. - Enable support reminder for models with severe overhangs without supports enabled - Pop-up dialogs are now created dynamically, improving boot times and reducing memory usage - Start and end G-code template formulas, along with end-of-print variable replacements (like total print time), are now processed directly within CuraEngine, contributed by @wawanbreton - Start and end G-code templates…

Full release notes from the publisher

Manifest: manifests/u/Ultimaker/Cura/5.14.0

Pin this version: winget install --id Ultimaker.Cura --version 5.13.0 --exact

Release notes

New features and improvements: - Added the new UltiMaker Factor 4+ printer, including profiles - Added option to specify file association during the installation of Cura for windows, contributed by @hellAholic New Settings: - Introduced Infill Start/End Preference settings that give control over the starting location of infill - Added Support Infill option "Lightning", and in addition the following supporting settings: Support Lightning Angle, Support Lightning Overhang Angle, Support Lightning Prune Angle, and Support Lightning Straightening Angle, which together allow you to add and control lightning infill generated for support structures - The Support Infill Line Multiplier has been introduced to increase the quantity of infill lines. When an even number of lines is specified through this setting and paired with lightning support, it produces a single extrusion line for each island - Introduced Minimum Hole Area in Brim Support, which filters out small holes in the support brim, resulting in a more consistent brim - Added Temperature Delta Top Surface, which allows you to print top surfaces at a different temperature - Added more options to Retract Before Outer Wall to give more control over retraction behavior when traveling to the outer wall - Added Initial Layer Wall Ordering which gives control over the order in which the walls are printed for the initial layer, contributed by @hellAholic Bug fixes: - Support blockers now function correctly even when assigned to a…

Full release notes from the publisher

Manifest: manifests/u/Ultimaker/Cura/5.13.0

Pin this version: winget install --id Ultimaker.Cura --version 5.12.1 --exact

Release notes

Bug fixes: - Fixed an issue where the export action for .makerbot file format would fail unexpectedly.

Full release notes from the publisher

Manifest: manifests/u/Ultimaker/Cura/5.12.1

Pin this version: winget install --id Ultimaker.Cura --version 5.12.0 --exact

Release notes

New features and improvements: Bridging behavior over rectangular empty spaces and infill are now placed in a smarter way. The bridge lines are now anchored to layers below where possible. Bridge lines can now also be interlaced for improved quality. Fewer mistakes, less wasted time. Settings for disabled extruders are now greyed out to prevent "ghost editing," where you might spend time fine-tuning the Printing Temperature or Retraction Distance for Extruder 2, only to realize later that the entire model was set to print with Extruder 1. Additionally, a warning appears in the Preview stage if your model is hidden because an extruder is unchecked. - Updated combing behavior for thin parts so it doesn't ooze over the walls by updating the behavior for Inside Travel Avoid Distance - Added a warning in the preview if the reason you are not seeing your model is that the extruder is unchecked - Self-intersecting infills like Grid, Triangular, and Cubic are hidden for some printers in recommended mode because they introduce artifacts at high speeds. They are still available in Custom mode - Added height of the layer in preview mode in mm in addition to the layer number, contributed by @HellAholic - Added a pop-up to help with using the Select Face mode when rotating a model, resolves Ultimaker/Cura#21359, contributed by @HellAholic - Improved the reliability and maintainability of the Cura UI and Post Processing plugin, contributed by @HellAholic - Added a new button under the…

Full release notes from the publisher

Manifest: manifests/u/Ultimaker/Cura/5.12.0

Pin this version: winget install --id Ultimaker.Cura --version 5.11.0 --exact

Release notes

Read the release notes on the publisher’s site

Manifest: manifests/u/Ultimaker/Cura/5.11.0

Pin this version: winget install --id Ultimaker.Cura --version 5.10.2 --exact

Release notes

UltiMaker S6 and S8 improvements: - Introduced the CC+ 0.6 core to the UltiMaker S6 and S8. This core delivers better results for demanding applications and will be replacing the CC+ 0.4 core. - Added new profiles for PC and CPE+ on UltiMaker S6 and S8 - Updated the default support type for the PETG material for UltiMaker S6 and S8 This release introduces print quality improvements for the UltiMaker S6 and S8 for carbon-filled printing. We intend to improve more non-engineering materials in a follow-up release.

Full release notes from the publisher

Manifest: manifests/u/Ultimaker/Cura/5.10.2

Pin this version: winget install --id Ultimaker.Cura --version 5.10.1 --exact

Release notes

The new UltiMaker S6 is here Print with the new UltiMaker S6 in Cura from day 1. The UltiMaker S6 is the newest addition to the S series of UltiMaker printers that carries forward the award-winning legacy of the S5, now supercharged with innovations like the UltiMaker Cheetah for up to 4x productivity. Learn more about this printer here. Other improvements: - Introduced Visual Intent profiles for PLA and Tough PLA for the UltiMaker S8 - Introduced High-Speed Intents for ABSR for Method X and Method XL Bug fixes: - Updated UltiMaker S8 profiles to significantly improve the quality of PC, CPE, CPE+, PETG, support structures, and dual extrusion prints - Support brims no longer listen to the Brim Distance setting, so the brims will always be attached to the support - Fixed a bug affecting multi-extruder printers where the initial temperature was not set correctly at the start of a print if all features used an extruder other than T0

Full release notes from the publisher

Manifest: manifests/u/Ultimaker/Cura/5.10.1

Pin this version: winget install --id Ultimaker.Cura --version 5.10.0 --exact

Release notes

Read the release notes on the publisher’s site

Manifest: manifests/u/Ultimaker/Cura/5.10.0

Pin this version: winget install --id Ultimaker.Cura --version 5.9.1 --exact

Release notes

Read the release notes on the publisher’s site

Manifest: manifests/u/Ultimaker/Cura/5.9.1

Pin this version: winget install --id Ultimaker.Cura --version 5.9.0 --exact

Release notes

Read the release notes on the publisher’s site

Manifest: manifests/u/Ultimaker/Cura/5.9.0

Pin this version: winget install --id Ultimaker.Cura --version 5.8.1 --exact

Release notes

Read the release notes on the publisher’s site

Manifest: manifests/u/Ultimaker/Cura/5.8.1

Pin this version: winget install --id Ultimaker.Cura --version 5.8.0 --exact

Release notes

Publisher changelog

Manifest: manifests/u/Ultimaker/Cura/5.8.0

Pin this version: winget install --id Ultimaker.Cura --version 5.7.2-RC2 --exact

Release notes

Publisher changelog

Manifest: manifests/u/Ultimaker/Cura/5.7.2-RC2

Pin this version: winget install --id Ultimaker.Cura --version 5.7.1 --exact

Release notes

Publisher changelog

Manifest: manifests/u/Ultimaker/Cura/5.7.1

Pin this version: winget install --id Ultimaker.Cura --version 5.7.0 --exact

Release notes

Publisher changelog

Manifest: manifests/u/Ultimaker/Cura/5.7.0

Pin this version: winget install --id Ultimaker.Cura --version 5.6.0 --exact

Release notes

- Prime Tower Base Size - Prime Tower Base Height - Prime Tower Base Slope - Prime Tower Raft Line Spacing - Introduced the setting for Raft Line Spacing, but for the prime tower - Updated the Support Z Distance to allow for more different values, no longer only multiple layerheights, solves #6105 - Fixed a crash for some Linux users when trying to open the file menu - Introduced Balanced and Solid profiles for 1C extruders to UltiMaker Method X and Method XL - Improved self-support for UltiMaker MethodX and MethodXL printers so the support extruder will not be used - The prime tower is now always enabled when the second extruder is used for the MethodX and MethodXL printers - Updated the default prime tower position so it doesn't prevent slicing for some printers - Fixed an issue where raft layers were partially printed - Slice information template variables were not available through start-end code formulas - Resolved an issue with 100% support roof for tree support, contributed by @ThomasRahm - Introduced Ender 3 V3 SE, contributed by @dim1triy - Updated bridge flows for UltiMaker PLA, TPLA and ABS to address pillowing in AA 0.8 for UltiMaker printers - Updated Spanish translation for Lightning infill, contributed by @Pelochus - Updated German translation for Laying object flat on buildplate, contributed by @gluetolf - Updated Brazilian translations, contributed by @Patola - The predicted printing time for dual extrusion printjobs on the Method series are deviating from…

Full release notes from the publisher

Manifest: manifests/u/Ultimaker/Cura/5.6.0

Pin this version: winget install --id Ultimaker.Cura --version 5.5.0 --exact

Release notes

- Modify generated gcode, postprocessing it per layer - Generate Infill patterns - Modify extrusion paths - Listen to a broadcast of all Settings - Introduced Max OSX builds for ARM64 (M1 support), next to our existing X64 builds. With major contributions from @TheSin - Introduced a single Linux build removing the need to have a different modern and regular Linux build. - UltiMaker printers with UltiMaker Materials have faster-predicted printing times as a result of a number of changed printing speeds - UltiMaker configurations with limited intents in the past like AA 0.8 cores, now have more intents available - Updated printing temperatures for UltiMaker printers to be more uniform - Updated Support Interface Settings for UltiMaker printers - Introduced a support material tag, so support is automatically printed with support material - Default has been updated to Balanced to reflect the perfect harmony between these visual, engineering, and draft profiles. - Use Tab to navigate between settings in the Per Model Settings window, solves #10967 - Introduced Ctrl-C and Ctrl-V next to the current multiply behavior, solves #8859 - Arrange your models in a grid with the same orientation with Grid Placement - A message that shows when your Removable Disk is out of space and prevents incomplete gcodes from being saved, solves #14273 - Add Printer and Printer Settings windows are now resizable to fit in more start/end gcode in an orderly way - Restored the color picker tool when…

Full release notes from the publisher

Manifest: manifests/u/Ultimaker/Cura/5.5.0

Pin this version: winget install --id Ultimaker.Cura --version 5.4.0 --exact

Release notes

- Improved slicing time for Tree Support - Introduced 10 new settings and updated 2 so anyone can tune the behavior - Updated options for Tree Support Rest Preference to be more correct - Fixed a bug where Tree Support would generate unsupported islands - Fixed a bug where slicing would fail if Preference was set to On Any Flat Surface - Fixed a bug where branches were not generated when Support Interface was enabled. - Fixed a bug where the Support Overhang Angle caused a crash with Tree Support - Fixed a bug where the Support Interface was not correctly generated with Tree Support - Updated the UltiMaker logo to reflect the new company logo - Added support for the updated mainboard revisions of UltiMaker S3, S5, and S7 - Introduced Hole Horizontal Expansion Max Diameter so only the expansion of smaller holes can be tuned while leaving larger holes untouched. - Introduced Skirt Height setting to make a skirt easier to remove - Improved the minimum layer time for printers with multiple extruders. - Improved accuracy of when the M104 Hotend Temperature command is added - Improved printing order of the prime tower to include a dual brim, primed every layer, and primed before and after the extruder switch. - Improved behavior for opening and closing categories when adding a new printer - Removed the settings related to Wire Printing since it was broken and barely used. - Upgraded PyQt to version 6.4.2 which improves responsiveness in the UI - Fixed a bug where the brim line…

Full release notes from the publisher

Manifest: manifests/u/Ultimaker/Cura/5.4.0

Pin this version: winget install --id Ultimaker.Cura --version 5.3.1 --exact

Release notes

Publisher changelog

Manifest: manifests/u/Ultimaker/Cura/5.3.1

Pin this version: winget install --id Ultimaker.Cura --version 5.3.0 --exact

Release notes

Publisher changelog

Manifest: manifests/u/Ultimaker/Cura/5.3.0

Release notes

Publisher changelog

Release notes

Publisher changelog